Recent Content by Pedro Ferreira

  1. Pedro Ferreira
    Post

    USB ports do not work anymore

    probably a dumb question but... have you powered down and up again your UDOO? anyway try this: power down, disconnect keyboard and mouse, power...
    Post by: Pedro Ferreira, Mar 24, 2016 in forum: UDOO QUAD
  2. Pedro Ferreira
    Post

    Connecting a camera module through the CSI port

    CSI is a big work, look here for more details: http://mipi.org/specifications/camera-interface The UDOO (from IMX6DQRM.pdf): Function High speed...
    Post by: Pedro Ferreira, Mar 20, 2016 in forum: UDOO QUAD
  3. Pedro Ferreira
    Post

    udoo quad I/O

    this project is also nice for ARM / FPGA...
    Post by: Pedro Ferreira, Mar 15, 2016 in forum: UDOO QUAD
  4. Pedro Ferreira
    Post

    udoo quad I/O

    GPIO toggle is not very fast, look around for "i.MX6 GPIO" and you'll find some info on that. Then you have a few SPI ports available, don't know...
    Post by: Pedro Ferreira, Mar 14, 2016 in forum: UDOO QUAD
  5. Pedro Ferreira
    Post

    Best way to program arduino without using arduino ide

    yes, I rebooted the UDOO and pressed space on u-boot prompt so I'm sure the Linux side didn't boot and was not interfering with the serial...
    Post by: Pedro Ferreira, Mar 11, 2016 in forum: Arduino IDE
  6. Pedro Ferreira
    Post

    openPOWERLINK EdrvFec driver

    This is a chicken / egg situation :-) if they have a board then they can integrate it in their test bench and more people will be looking at UDOO...
    Post by: Pedro Ferreira, Mar 11, 2016 in forum: Networking
  7. Pedro Ferreira
    Post

    Best libgl provider?

    ok, done!
    Post by: Pedro Ferreira, Mar 11, 2016 in forum: UDOO QUAD
  8. Pedro Ferreira
    Thread

    openPOWERLINK EdrvFec driver

    Hi UDOO Team, I'm using the UDOO Quad for prototyping and I'm also using openPOWERLINK to connect the UDOO Quad to a B&R PLC. It works fine with...
    Thread by: Pedro Ferreira, Mar 10, 2016, 2 replies, in forum: Networking
  9. Pedro Ferreira
    Post

    Best way to program arduino without using arduino ide

    Ho and I tried Using Arduino IDE without UDOO DUAL/QUAD patch from this page and it didn't work... I unplugged J18, then reset with J22 for 1 sec,...
    Post by: Pedro Ferreira, Mar 10, 2016 in forum: Arduino IDE
  10. Pedro Ferreira
    Post

    Best way to program arduino without using arduino ide

    On this other resources page I found a link to another Arduino package git... Its everywhere... I'll try to make sense of all this next week end...
    Post by: Pedro Ferreira, Mar 10, 2016 in forum: Arduino IDE
  11. Pedro Ferreira
    Post

    Best way to program arduino without using arduino ide

    Your first link looks interesting, the udoo-arduino-cli. I'll try it this week and. I don't have Arduino installed by default in Arch Linux. Where...
    Post by: Pedro Ferreira, Mar 10, 2016 in forum: Arduino IDE
  12. Pedro Ferreira
    Post

    Best way to program arduino without using arduino ide

    I want to use the UDOO for automation prototyping so I'm using Arch Linux ARM preempt with rt patch (thanks to osnwt from the Arch Linux ARM...
    Post by: Pedro Ferreira, Mar 10, 2016 in forum: Arduino IDE
  13. Pedro Ferreira
    Thread

    Best way to program arduino without using arduino ide

    Hi all, I want to program the Arduino inside the UDOO Quad directly from Linux, without using the IDE or the external UBS port. What is the best...
    Thread by: Pedro Ferreira, Mar 8, 2016, 9 replies, in forum: Arduino IDE