Hello everyone! I've just bought an UDOO Quad, arrived this morning. First try was to put ArchLinux on my new 8GB MicroSD card (specifically bought for UDOO), but, here what I got when I tried to debug by serial: Code: U-Boot 2013.10-rc3 (Jan 20 2014 - 13:33:34) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Board: UDOO DRAM: 1 GiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment No panel detected: default to LDB-WVGA Display: LDB-WVGA (800x480) In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME] Warning: failed to set MAC address Hit any key to stop autoboot: 0 UDOO board => boot mmc0 is current device ** File not found boot.scr ** 4372712 bytes read in 289 ms (14.4 MiB/s) Booting from mmc ... ** File not found imx6q-udoo.dtb ** ## Booting kernel from Legacy Image at 12000000 ... Image Name: Linux-3.0.35 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4372648 Bytes = 4.2 MiB Load Address: 10008000 Entry Point: 10008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.0.35 (udoo@ubuntu) (gcc version 4.4.4 (4.4.4_09.06.2010) ) #1 SMP PREEMPT Mon Mar 3 15:17:07 CET 2014 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: SECO i.Mx6 UDOO Board [ 0.000000] Kernel ver: v. 127\nMemory policy: ECC disabled, Data cache writealloc [ 0.000000] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.000000] PERCPU: Embedded 7 pages/cpu @8c008000 s5504 r8192 d14976 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227328 [ 0.000000] Kernel command line: console=ttymxc1,115200 root=/dev/mmcblk0p1 rootwait rw fbmem=24M video=mxcfb0:dev=hdmi,1920x1080M@60,bpp=32 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 640MB 256MB = 896MB total [ 0.000000] Memory: 895872k/895872k available, 152704k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] DMA : 0xf4600000 - 0xffe00000 ( 184 MB) [ 0.000000] vmalloc : 0xc0800000 - 0xf2000000 ( 792 MB) [ 0.000000] lowmem : 0x80000000 - 0xc0000000 (1024 MB) [ 0.000000] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) [ 0.000000] modules : 0x7f000000 - 0x7fe00000 ( 14 MB) [ 0.000000] .init : 0x80008000 - 0x8003a000 ( 200 kB) [ 0.000000] .text : 0x8003a000 - 0x80b7851c (11514 kB) [ 0.000000] .data : 0x80b7a000 - 0x80be1460 ( 414 kB) [ 0.000000] .bss : 0x80be1484 - 0x80c32bc0 ( 326 kB) [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:624 [ 0.000000] MXC GPIO hardware [ 0.000000] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms [ 0.000000] arm_max_freq=1GHz [ 0.000000] MXC_Early serial console at MMIO 0x21e8000 (options '115200') [ 0.000000] bootconsole [ttymxc1] enabled [ 0.000000] Console: colour dummy device 80x30 [ 0.217847] Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280) [ 0.306187] pid_max: default: 32768 minimum: 301 [ 0.311079] Mount-cache hash table entries: 512 [ 0.316339] Initializing cgroup subsys cpuacct [ 0.320840] Initializing cgroup subsys devices [ 0.325299] Initializing cgroup subsys freezer [ 0.329791] Initializing cgroup subsys blkio [ 0.334129] CPU: Testing write buffer coherency: ok [ 0.339284] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available [ 0.439815] CPU1: Booted secondary processor [ 0.519812] CPU2: Booted secondary processor [ 0.599835] CPU3: Booted secondary processor [ 0.639320] Brought up 4 CPUs [ 0.655149] SMP: Total of 4 processors activated (6324.22 BogoMIPS). [ 0.661953] devtmpfs: initialized [ 0.682046] print_constraints: dummy: [ 0.686006] NET: Registered protocol family 16 [ 0.694900] print_constraints: vddpu: 725 <--> 1300 mV at 1150 mV fast normal [ 0.702488] print_constraints: vddcore: 725 <--> 1300 mV at 1150 mV fast normal [ 0.710235] print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal [ 0.717905] print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal [ 0.725674] print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal [ 0.733360] print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal [ 0.742475] [ 0.742481] > UDOO quad [ 0.746253] > rev C Called set_gpios_direction [ 0.750933] Test and set gpios directions and values by Gionji feat. Ekirei test [ 0.782784] Resetting ethernet physical layer. [ 0.826230] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. [ 0.833067] hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step. [ 0.840427] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.846314] L310 cache controller enabled [ 0.850357] l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x02070000, Cache size: 1048576 B [ 0.886816] bio: create slab <bio-0> at 0 [ 0.894076] mxs-dma mxs-dma-apbh: initialized [ 0.898782] print_constraints: vmmc: 3300 mV [ 0.903880] vgaarb: loaded [ 0.907383] SCSI subsystem initialized [ 0.912257] usbcore: registered new interface driver usbfs [ 0.917884] usbcore: registered new interface driver hub [ 0.923405] usbcore: registered new device driver usb [ 0.928477] Freescale USB OTG Driver loaded, $Revision: 1.55 $ [ 0.949319] imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7) [ 0.969318] imx-ipuv3 imx-ipuv3.1: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7) [ 0.977157] mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 driver probed [ 0.983637] mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 dphy version is 0x3130302a [ 0.991361] MIPI CSI2 driver module loaded [ 0.995699] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 1.002893] Bluetooth: Core ver 2.16 [ 1.006593] NET: Registered protocol family 31 [ 1.011064] Bluetooth: HCI device and connection manager initialized [ 1.017442] Bluetooth: HCI socket layer initialized [ 1.022342] Bluetooth: L2CAP socket layer initialized [ 1.027491] Bluetooth: SCO socket layer initialized [ 1.032835] cfg80211: Calling CRDA to update world regulatory domain [ 1.040263] i2c-core: driver [max17135] using legacy suspend method [ 1.046550] i2c-core: driver [max17135] using legacy resume method [ 1.052779] Switching to clocksource mxc_timer1 [ 1.073357] NET: Registered protocol family 2 [ 1.077936] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 1.085815] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 1.095154] TCP bind hash table entries: 65536 (order: 7, 786432 bytes) [ 1.102892] TCP: Hash tables configured (established 131072 bind 65536) [ 1.109542] TCP reno registered [ 1.112700] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 1.118681] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 1.125399] NET: Registered protocol family 1 [ 1.130100] RPC: Registered named UNIX socket transport module. [ 1.136040] RPC: Registered udp transport module. [ 1.140780] RPC: Registered tcp transport module. [ 1.145500] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.152913] PMU: registered new PMU device of type 0 [ 1.158052] Static Power Management for Freescale i.MX6 [ 1.163296] wait mode is enabled for i.MX6 [ 1.167611] cpaddr = c0880000 suspend_iram_base=c08fc000 [ 1.173020] PM driver module loaded [ 1.176917] IMX usb wakeup probe [ 1.180652] add wake up source irq 75 [ 1.187976] IMX usb wakeup probe [ 1.191511] cpu regulator mode:ldo_enable [ 1.195729] i.MXC CPU frequency driver [ 1.226443] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 1.233360] fuse init (API version 7.16) [ 1.238215] msgmni has been set to 1749 [ 1.243613] alg: No test for stdrng (krng) [ 1.247895] io scheduler noop registered [ 1.251831] io scheduler deadline registered [ 1.256203] io scheduler cfq registered (default) [ 1.262040] MIPI DSI driver module loaded [ 1.266244] mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver hdmi [ 1.272759] mxc_hdmi mxc_hdmi: Detected HDMI controller 0x13:0xa:0xa0:0xc1 [ 1.279682] fbcvt: 1920x1080@60: CVT Name - 2.073M9 [ 1.284583] fb_videomode = 59 1920 1080 5780 328 128 3 32 200 5 2 0 32 [ 1.303302] imx-ipuv3 imx-ipuv3.0: WARNING: adapt panel end blank lines [ 1.317424] imx-ipuv3 imx-ipuv3.0: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7) [ 1.350735] imx-ipuv3 imx-ipuv3.0: WARNING: adapt panel end blank lines [ 1.384118] Console: switching to colour frame buffer device 160x64 [ 1.432191] mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver ldb [ 1.438607] _regulator_get: get() with no identifier [ 1.450293] mxc_sdc_fb mxc_sdc_fb.2: register mxc display driver ldb [ 1.461459] imx-sdma imx-sdma: loaded firmware 1.1 [ 1.470561] imx-sdma imx-sdma: initialized [ 1.606282] Serial: IMX driver [ 1.609483] imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX [ 1.616360] imx-uart.1: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX [ 1.622858] console [ttymxc1] enabled, bootconsole disabled [ 1.622858] console [ttymxc1] enabled, bootconsole disabled [ 1.634441] imx-uart.3: ttymxc3 at MMIO 0x21f0000 (irq = 61) is a IMX [ 1.646609] loop: module loaded [ 1.650175] request BOSSA_CLK IRQ [ 1.653493] registering IRQ 419 for BOSSAC Arduino erase/reset operation [ 1.703324] No sata disk. [ 1.707261] GPMI NAND driver registered. (IMX) [ 1.715869] vcan: Virtual CAN interface driver [ 1.720345] CAN device driver interface [ 1.724184] flexcan netdevice driver [ 1.727961] FEC Ethernet Driver [ 1.733365] fec_enet_mii_bus: probed [ 1.738354] usbcore: registered new interface driver rt2800usb [ 1.744191] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.750857] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller [ 1.757506] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 [ 1.787386] fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000 [ 1.807379] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00 [ 1.813652] hub 1-0:1.0: USB hub found [ 1.817429] hub 1-0:1.0: 1 port detected [ 1.821531] add wake up source irq 72 [ 1.825228] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller [ 1.831882] fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2 [ 1.877375] fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200 [ 1.907366] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00 [ 1.913552] hub 2-0:1.0: USB hub found [ 1.917315] hub 2-0:1.0: 1 port detected [ 1.921595] Initializing USB Mass Storage driver... [ 1.926630] usbcore: registered new interface driver usb-storage [ 1.932698] USB Mass Storage support registered. [ 1.937616] usbcore: registered new interface driver usbserial [ 1.943550] USB Serial support registered for generic [ 1.948734] usbcore: registered new interface driver usbserial_generic [ 1.955265] usbserial: USB Serial Driver core [ 1.959744] USB Serial support registered for debug [ 1.964743] usbcore: registered new interface driver debug [ 1.970248] ARC USBOTG Device Controller driver (1 August 2005) [ 1.976522] g_ether gadget: using random self ethernet address [ 1.982384] g_ether gadget: using random host ethernet address [ 1.988971] usb0: MAC d2:9a:58:17:a8:b6 [ 1.992811] usb0: HOST MAC 7e:97:a8:bb:a4:b5 [ 1.997088] g_ether gadget: controller 'fsl-usb2-udc' not recognized; trying CDC Ethernet (ECM) [ 2.005826] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 [ 2.012461] g_ether gadget: g_ether ready [ 2.016474] Suspend udc for OTG auto detect [ 2.047388] fsl-usb2-udc: bind to driver g_ether [ 2.052653] mousedev: PS/2 mouse device common for all mice [ 2.058663] usbcore: registered new interface driver usbtouchscreen [ 2.065362] Sitronix touch driver 2.9.1 [ 2.069217] Release date: 20120507 [ 2.073022] sitronix_reset_ic [ 2.196253] send status reg command error (-5) [ 2.200719] sitronix: probe of 2-0055 failed with error -5 [ 2.206663] i2c-core: driver [isl29023] using legacy suspend method [ 2.212948] i2c-core: driver [isl29023] using legacy resume method [ 2.219878] snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc0 [ 2.226545] i2c /dev entries driver [ 2.230856] Linux video capture interface: v2.00 [ 2.257406] usb 2-1: new high speed USB device number 2 using fsl-ehci [ 2.367465] ov5640_read_reg:write reg error:reg=300a [ 2.372431] camera ov5640_mipi is not found [ 2.377036] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video16 [ 2.384681] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17 [ 2.392366] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video18 [ 2.400009] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video19 [ 2.407648] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video20 [ 2.415416] vivi-000: V4L2 device registered as video2 [ 2.420575] Video Technology Magazine Virtual Video Capture Board ver 0.8.0 successfully loaded. [ 2.429894] usbcore: registered new interface driver uvcvideo [ 2.435672] USB Video Class driver (v1.1.0) [ 2.440550] hub 2-1:1.0: USB hub found [ 2.440588] i2c-core: driver [mag3110] using legacy suspend method [ 2.440595] i2c-core: driver [mag3110] using legacy resume method [ 2.441051] imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1) [ 2.441163] Bluetooth: Virtual HCI driver ver 1.3 [ 2.441395] Bluetooth: HCI UART driver ver 2.2 [ 2.441402] Bluetooth: HCIATH3K protocol initialized [ 2.441408] Bluetooth: Generic Bluetooth USB driver ver 0.6 [ 2.441546] usbcore: registered new interface driver btusb [ 2.441701] sdhci: Secure Digital Host Controller Interface driver [ 2.441707] sdhci: Copyright(c) Pierre Ossman [ 2.442043] mmc0: SDHCI controller on platform [sdhci-esdhc-imx.2] using DMA [ 2.507485] hub 2-1:1.0: 4 ports detected [ 2.510685] mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed [ 2.518990] VPU initialized [ 2.522342] mxc_asrc registered [ 2.546957] Thermal calibration data is 0x5734df69 [ 2.551765] Thermal sensor with ratio = 180 [ 2.567375] Anatop Thermal registered as thermal_zone0 [ 2.572666] anatop_thermal_probe: default cooling device is cpufreq! [ 2.581589] usbcore: registered new interface driver usbhid [ 2.587166] usbhid: USB HID core driver [ 2.591493] usbcore: registered new interface driver snd-usb-audio [ 2.598235] mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio [ 2.603686] Cirrus Logic CS42888 ALSA SoC Codec Driver [ 2.608943] i2c-core: driver [cs42888] using legacy suspend method [ 2.615126] i2c-core: driver [cs42888] using legacy resume method [ 2.654725] mmc0: new high speed SDHC card at address e624 [ 2.660624] mmcblk0: mmc0:e624 SS08G 7.40 GiB [ 2.666320] mmcblk0: p1 [ 2.703883] audio_codec_ac97_cold_reset [ 2.789945] Found Audio codec AC97 vt1613, [ID = 5649 - 4123] [ 2.808164] asoc: vt1613 <-> imx-ssi.0 mapping ok [ 2.814525] imx_3stack asoc driver [ 2.819513] asoc: mxc-hdmi-soc <-> imx-hdmi-soc-dai.0 mapping ok [ 2.826178] ALSA device list: [ 2.827531] usb 2-1.3: new high speed USB device number 3 using fsl-ehci [ 2.835880] #0: vt1613-audio [ 2.838947] #1: imx-hdmi-soc [ 2.842204] NET: Registered protocol family 26 [ 2.847183] TCP cubic registered [ 2.850426] NET: Registered protocol family 17 [ 2.854883] can: controller area network core (rev 20090105 abi 8) [ 2.861141] NET: Registered protocol family 29 [ 2.865587] can: raw protocol (rev 20090105) [ 2.869896] can: broadcast manager protocol (rev 20090105 t) [ 2.875657] Bluetooth: RFCOMM TTY layer initialized [ 2.880555] Bluetooth: RFCOMM socket layer initialized [ 2.885696] Bluetooth: RFCOMM ver 1.11 [ 2.889454] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 2.894766] Bluetooth: BNEP filters: protocol multicast [ 2.900000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 2.906089] lib80211: common routines for IEEE802.11 drivers [ 2.911789] Registering the dns_resolver key type [ 2.916531] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 2.924575] Bus freq driver module loaded [ 2.928632] Bus freq driver Enabled [ 2.933912] mxc_dvfs_core_probe [ 2.937260] DVFS driver module loaded [ 2.942552] snvs_rtc snvs_rtc.0: setting system clock to 1970-01-01 00:00:00 UTC (0) [ 2.953282] EXT3-fs: barriers not enabled [ 2.961580] kjournald starting. Commit interval 5 seconds [ 2.964673] EXT3-fs (mmcblk0p1): using internal journal [ 2.964685] EXT3-fs (mmcblk0p1): mounted filesystem with writeback data mode [ 2.964715] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 2.966281] devtmpfs: mounted [ 2.966339] Freeing init memory: 200K U-Boot 2013.10-rc3 (Jan 20 2014 - 13:33:34) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Board: UDOO DRAM: 1 GiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment No panel detected: default to LDB-WVGA Display: LDB-WVGA (800x480) In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME] Warning: failed to set MAC address Now I put UDOObuntu on MicroSD card, and then updated kernel from "udooupdate.sh" on my laptop with that: Code: sudo ./udooupdate.sh --root=<SD_MOUNTED_PATH> --cpu=quad but same story... What can I do to solve? Thanks!
Try to reflash you Micro SDcard with the last UDOObuntu without using the udooupdate and let me know.
Hello every one, I have the same problem with my UDOO Quad. I follow the tutorial in order to flash the image downloaded into a SD card but, at start, it stop after: Code: [ 2.966339] Freeing init memory: 200K Any idea? Thanks Alessandro
Mine pauses at that point and then continues to boot. That pause is usually around 3 seconds. Have you waited longer than that? Here's my output from UDOObuntu 1.0. BTW it looks like your SD card is faster than mine! Code: [ 3.440609] devtmpfs: mounted [ 3.443647] Freeing init memory: 200K [ 6.731279] ERROR: v4l2 capture: slave not found! [ 6.734931] ERROR: v4l2 capture: slave not found! [ 8.633811] imx-ipuv3 imx-ipuv3.0: WARNING: adapt panel end blank lines
hello! i've the same problem with my udoo quad. I had not upgrade the uboot. someone has the solution? I've installed the new openelec my outpout is: Code: U-Boot 2015.07 (Aug 02 2015 - 12:20:18 +0000) CPU: Freescale i.MX6Q rev1.2 996 MHz (running at 792 MHz) Reset cause: POR Board: Udoo Quad DRAM: 1 GiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME] Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 reading uEnv.txt 616 bytes read in 12 ms (49.8 KiB/s) Importing environment from mmc (uEnv.txt)... Checking if uenvcmd is set ... Running default loadimage ... reading /KERNEL **Unable to read file /KERNEL =>
Sandroelec, try to follow the given suggestions. If you don't manage to solve your problem, then open a ticket and we'll take care of you. Cheers
hello everybody, i've tried again to install openElec for m udoo quad. It doesn't work again, same error cannot loading kernel. but the size of the image unzipped is only 292 MB it's correct? thank
I'm affraid I can't help much.As I wrote I can boot both images (quad and universal). If not I would not publish them. And yes, size around 300 MB is correct. Second (storage) partition is resized on first boot.
